AMMCO 7000 PDF

View and Download AMMCO installation instructions manual online. Disc Rotor Lathe. Lathe pdf manual download. iv • AMMCO Brake Lathes. Safety. Safety Notices and. Decals. For your safety, and the safety of others, read and understand all of the safety notices and . Get AMMCO Disc Rotor Lathe Manual. Get all AMMCO manuals!.

Author: Nikonos Kizragore
Country: Slovenia
Language: English (Spanish)
Genre: Finance
Published (Last): 1 October 2007
Pages: 362
PDF File Size: 20.40 Mb
ePub File Size: 12.54 Mb
ISBN: 128-9-73484-121-5
Downloads: 15188
Price: Free* [*Free Regsitration Required]
Uploader: Kaktilar

AMMCO 7000 Hustler Disc Brake Lathe Operation Manual

Page 14 Turn the left hand tool bit control until the tool bit contacts the rotor surface and makes a scratch cut no deeper than. The patented self-aligning spacer prevents diagonal thrust on the adapters. Loosen the stud nut, Fig.

Clean, repair, remount, or replace as necessary. After the brake rotor is mounted on the arbor, install the silencer band.

Comments to this Manuals Your Name. B 10, and adjust the twin cutter so that the rotor is centered between the tool bits. The cross also be operated manually using the cross feed handwheel.

AMMCO Hustler Disc Brake Lathe Operation Manual | eBay

Proper maintenance and inspection is necessary for safe operation. Do this for your own protection. Turn the cross feed handwheel back about a half turn, start the lathe and move the tool bit in to make a second scratch cut. This is caused by runout or wobble due to rotor condition amco by the way the rotor is mounted on the arbor.

  APRILOVE DIEVCA PDF

What’s missing? Tell us about it.

Safety Notices And Decals For additional copies of either, or further information, contact: Also always wear safety glasses or a face shield. Brake Lathes Cross Feed – The cross feed draws the twin tool bits across the face of a brake rotor when the cross feed drive is engaged.

READ these instr uctions bef ore placing unit in. This is easily done by stretching the band to its full length and then wrapping it around the rotor and hooking the end metal loop over a lead weight, Fig. Reconditioning Disc Brake Rotors The patented self-aligning spacer prevents diagonal thrust on the adapters. Center the twin cutter to the rotor. Got it, continue to print.

When the cross feed has moved the cutting tools all the way across the face of the rotor, the feed will shut off automatically. Also review the following general safety instructions. Table of Contents Add to my manuals Add.

Warning This equipment incorporates parts such as snap switches and power receptacles which tend to produce arcs or sparks. Page 4 Safety Safety Notices and Decals For your safety, and the safety of others, read and understand all of the safety notices and decals included here and on the unit.

  JAMES CORNER TERRA FLUXUS PDF

Wmmco these and other materials delivered. Turn the left hand tool bit control until the tool bit contacts the rotor surface and makes a scratch cut no deeper than. Important Safety Instructions Safety glasses, goggles, or a face shield contact persons in the area causing personal injury.

Maintain unit properly, keep work surfaces and work area clean. DO NOT throw them into a box. Tell us what’s missing. If any of the goods called for on this bill of lading are shorted or damaged, do not accept them until the carrier makes a notation on the freight bill of the shorted or damaged goods. Adjust the drive belt to match the rotor size. Page 15 Examine each adapter and the arbor for nicks, burrs, chips, dirt, and rust.

Don’t have an account? Page 15 Brake Lathes The scratch will usually appear as an incomplete circle.

Repeat the procedure for the other tool-bit holder. Tell us about it. Either rough or finish cuts may be taken to resurface a rotor.

Make sure that the tool bits clear the rotor faces and the silencer band.