ASTM B specification covers Nickel Copper Alloys like Monel Alloy Round Bar with ASTM B UNS N in the form of hot-worked and cold- worked. Designation: B – 03 Standard Speci?cation for Nickel-Copper Alloy Rod, Bar , and Wire1 This standard is issued under the?xed. Monel is a corrosion resistant NiCu easily machined, and fabricated. ASTM B, ASTM B, QQ-N Class A, UNS N Available in bar, wire.
|Published (Last):||26 January 2005|
|PDF File Size:||1.85 Mb|
|ePub File Size:||19.12 Mb|
|Price:||Free* [*Free Regsitration Required]|
Material is thermally treated to relieve the major portion of the internal stresses resulting from cold-working and may have a very thin light to medium oxide. Workmanship, Finish, and Appearance 8. Monel Round Bars has excellent cryogenic and heat ranges. May be used to handle hydrochloric acid, but the presence of oxidizing salts will greatly accelerate corrosive attack. Notch length shall not exceed 1 in.
Villares Metals International
Rod and Bar, All sizes A B 85 85 80 85 80 50 50 50 50 45 8B 15 15 15B,C 15 30 30 25 35 — — — — — — — — 75 75 70 70 35 35 30 25 See Link to Active This link will always route to the current Active version of the standard.
Pickling bat heating coils. Hot-worked material to be machined in longer lengths should be speci? Plant for the refining satm uranium and isotope separation in the production of nuclear fuel.
Reproduction of this site in whole or part is prohibited without the expressed permission of High Performance Alloys, Inc. Preparation for Delivery Bb164 This standard has been approved for use by agencies of the Department of Defense.
A low corrosion rate in rapidly flowing seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions. These rates are for carbide tools, Type C-2 for roughing, drilling and reaming.
ASTM B Standard Specification for Nickel-Copper Alloy Rod, Bar, and Wire1_百度文库
For each lbs. The materials for rod, bar, or g164 shall conform to the mechanical properties specified by the reference material. ASTM B specification covers nickel-copper alloys the form of hot-worked and cold-worked rod, bar, round bar and wire.
The allowances for hot-worked material in Table 5 are recommended for rods machined in lengths of 3 ft 0.
ASTM B164 Round Bar | Monel 400 Round Bar Suppliers
B Under 1 Tensile specimens for rod and bar ? Recalibration shall be performed at least once per 8 h shift.
Provides for better surface inspection than does hot-worked material and often employed where welding is involved where removal of mill oxide is desired. When a full cross-section size test cannot be performed, the largest possible round specimen shown in Test Methods E 8 shall be used. Monel is widely used in the chemical, oil and marine industries.
ASTM B – 03() Standard Specification for Nickel-Copper Alloy Rod, Bar, and Wire
Excellent resistance to chloride ion stress corrosion cracking. Offer on Fasteners Sitemap. E Forging quality is furnished to chemical requirements and surface inspection only. The position and amplitude of the response from each note shall be marked on the instrument screen or a transparent overlay, and these asstm shall be used as the evaluation reference.
Monel is characterized by good general corrosion resistance, good weldability and moderate to high strength. The material shall conform to the chemical composition limits specified by the reference material.
Good resistance to sulfuric and hydrofluoric acids. NOTE 1—Hot-worked rectangular bar in widths 10 in.
In such cases, the user should run pilot forging tests to ensure himself that such material has the desired hot malleability range. Heat exchangers in a variety of industries. Intended primarily for hot heated bolts but is of somewhat inferior quality, as to surface seams and cracks compared to forging quality, astmm X1. The values given in parentheses b64 mathematical conversions to SI units that are provided for information only and are not considered standard.
High Performance Alloys stocks and produces Monel in this grade in the following forms: Material is selected from heats of known, good hot malleability. Specimens shall be free from sharp bends or kinks. Characteristics Corrosion resistance in an extensive range of marine and chemical environments.
C The maximum curvature depth of chord shall not exceed the values indicated multiplied by the length in feet. Machining Type Suggested starting rates are: